| Customization: | Available |
|---|---|
| Type: | Signal Repeater |
| Transmission Medium: | Wireless |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
Dual-Band 23dBm GSM900 DCS1800 2G 4G Repeater RF Mobile Amplifier Cell Phone GSM Signal Booster
Specifications:
| Frequency | Uplink | Downlink | |
| GSM900 | DCS1800 | 890 - 915/1710 - 1785MHz | 935 -960/1805-1880MHz |
| Operation Bandwidth | Wide Band | ||
| Gain | ≥70dB | ≥75dB | |
| Output Power | ≥18dBm | ≥23dBm | |
| MGC (Manual Gain Control) | 31dB Range/1dB step | ||
| Ripple in Band | 8dB | ||
| Noise Figure | ≤ 6dB | ||
| VSWR | ≤2.0 | ||
| Automatic Level Control | ≥20dB | ||
| Intermodulation Products | ≤ -40dBc | ||
| Spurious Emission | 9KHz~1GHz | ≤ -36dBm/30KHz | |
| 1GHz~12.75GHz | ≤ -30dBm/30KHz | ||
| Frequency stability | ≤ 0.01ppm | ||
| MTBF | > 50000 hours | ||
| Time Delay | ≤1.5μs | ||
| Impedance | 50Ω | ||
| Power Supply | Input: AC 110~240V; Output: DC 9V/5A | ||
| LED Alarm | Power LED | DC ON/OFF | |
| Smart LED | Smart function ON/OFF | ||
| AGC Alarm | Alarm RED when ALC 5dB-10dB | ||
| ISO Alarm | Alarm RED when ALC 15dB-20dB, Then Repeater will Auto Shut Down. Auto restart after two minutes. | ||
| Mechanical Specification | |||
| RF Connector | N-Female | ||
| Power Consumption | 25W | ||
| Operating Temperature | -10ºC~ +55ºC | ||
| Environment Conditions | IP40(Indoor) | ||
| Installation Type | Wall Installation | ||
| Dimensions (D x W x H ) | 228*170*65mm | ||
| Weight | ≤ 3.5 KG | ||
Description:
The signal amplifier of the mobile phone is composed of an antenna, a radio frequency duplexer, a low noise amplifier, a mixer, an attenuator, a filter, a power amplifier, and the like, and a downlink amplifying carrier. The basic principle of its work is: use the forward antenna (donor antenna) to receive the downlink signal of the base station into the repeater, amplify the useful signal through the low noise amplifier, suppress the noise signal in the signal, and improve the signal to noise ratio (S / N After being down-converted to the intermediate frequency signal, filtered by the filter, amplified by the intermediate frequency, then frequency-shifted up to the RF, amplified by the power amplifier, transmitted by the backward antenna (retransmission antenna) to the mobile station; The uplink signal of the mobile station is received, and is amplified by the uplink along the opposite path: that is, by the low noise amplifier, the down converter, the filter, the intermediate amplifier, the upconverter, and the power amplifier are retransmitted to the base station. Thereby achieving two-way communication between the substrate and the mobile station.
The LCD Repeater covers all existing wireless public communications networks:
GSM900&DCS1800
The LCD Repeaters have many intelligent functions: such as antenna isolation detection, Input & Output signal strength indication, system indication, manual gain control and smart mode. See the detailed introduction listed below:
The Display will auto-off if don't touch it in one minute.
1. "GREETWIN" is Company LOGO.
2. Power: Power supply with indicator.
3. Smart: Smart function with indicator. AUTO Mode now.
4. M: "AUTO" switch to "MANU".
5. Sel: Select the working systems,
long press the button for 2s, will enter into 900M. then setting the gain.
then set the gain 65dB, long press the button for 2s again. 65dB was confirmed.
6. 900MHz: Show the current working system. Press "Sel" to change to the different systems for operation.
7. AUTO/MANU: Automatic Mode or Manual gain Mode.
8. AGC: Automatic gain control with indicator.
9. ISO: Isolation inspection with indicator.
10. 63dB/68dB: gain of the working system.
11. 0dBm/0dBm: outpower of the working system.
12. UL is Uplink, DL is the downlink. "+" is increasing the gain, "-" is decreasing the gain.
Features:
1. Isolation Inspection. When the first power on the repeater, the device will automatically detect the isolation between the donor antenna and the service antenna. The users could easier see the status and make the adjustment accordingly.
2. Input&Output Signal Strength Indication. The specific number of uplinks and downlinks measured in Output Power(dBm). Easy for users' understanding.
3. Manual Gain Adjustment. The users or engineers could reduce the gain of the repeater manually via the buttons below the screen. The uplink and downlink gain could be set independently. "+" is increasing the gain, "-" is decreasing the gain.
4. Automatic Gain Control. Automatic Gain Control (AGC) is a dynamic gain adjustment feature with a 31dB range.
5. Smart Mode = AUTO Mode. The repeater could automatically change the gain according to the specific environment when the smart function is on. Please note that when the SMART is on, users could not able to set the gain manually. Gain reduce 31dB automatically at first, then AGC Alarm RED when AGC control 5dB-10dB, ISO Alarm RED when AGC control 20dB-25dB, Repeater will Auto Shut Down. Auto restart after two minutes.
6. MANU Mode, users can set the gain manually. AGC Alarm RED when AGC control 5dB-10dB ;
ISO Alarm RED when AGC control 20dB-25dB, Repeater will Auto Shut Down.
Auto restart after two minutes.
7. Auto Shut Down = ISO. Auto Shut Down is a stage that temporarily stops the RF function. If the input power reduces to a safe range for the repeater to operate, the software would power the repeater back on and restore all functions promptly. However, if the input power remains too great and dangerous for the network, it will then shut down completely. In such a case, the signal is too strong for the usage of the repeater.
1) Donor antenna: Recommend to use wideband panel antenna (7~14dBi gain) or Yagi antenna, better to use an antenna with good direction, high gain, and decoration shall be considered if it is in urban areas.
2) Role: It picks up signals from the tower, and sends it to the booster through cables, at the same time, it transmits the amplified mobile signals from the booster to the tower.
3) Server antenna: Recommend to use indoor Omni or panel antenna. Indoor Omni is suitable for wide-open areas where the signals can be radiated from the center to the surroundings, while the indoor panel is suitable for those narrow and long areas, like tunnels, corridors, elevators, etc.
4) Cables: 5D-FB or 7D-FB coaxial cables.
5) Power supply: Booster power adapter, a desktop standard. Usually directly connected to a power outlet. But preferably equipped with an air switch, groundings, sometimes a surge arrestor shall be connected.
Q1. Could I get a sample before bulk order?
Yes, we offer the sample for all models but charged.
Q2. What should I do if I don't know about frequency in my country?
Please feel free to contact us with your inquiry, we will find the frequency you need and address your problems.
Q3. Do you accept OEM/ODM order?
Yes, we can customize the brand logo, colors, and frequencies.
Q4.Shipment Date
| Sample | 3-5 business days |
| <20 pcs | 7-15 days |
| 20-50 pcs | 15-24 days |
| >50 pcs | Negotiate |
| USA/Canada/Europe/Asia | 3-5 days |
| Middle East/Latin American | 5-7 days |
| African | 3-7 days |
Q6.Payment Method
T/T, Western Union, Paypal, and Credit Card are available,
but we suggest paying by Alibaba Trade Assurance, the most favor, and security method.
*Other methods please contact us with more details.
Q7.Others
(1)Frequency
We can customize Single/Double/Triple/Quand/Penta Band for cellphone signal like 2G/3G/4G(GSM/CDMA/DCS/PCS/WCDMA/LTE, etc,)
(2)Output Power &Coverage Areas
| Output Power | Coverage Areas |
| 20dBm | 500-1500m² |
| 23dBm | 1500-2500m² |
| 25dBm | 2500-4000m² |
| 27dBm | 3000-5000m² |
| 30dBm | 5000-8000m² |
*Coverage is related to local signal strength, please contact us with your local condition, we can offer the best solution.
(3)Antenna
Cellphone signal booster must attach one indoor antenna and one outdoor antenna by two coaxial cables.
Website's price only includes a signal booster, please contact us if you need one set of devices with antenna, splitter, and coupler.
){kind=link}