23dBm Dual Band 3G 4G Lte1800 WCDMA2100 Signal Repeater Mobile Amplifier Cell Phone Signal Booster

• Type: Signal Repeater
• Transmission Medium: Wireless
• Standard: Standard
• Lightning Protection: With Lightning Protection
• Certification: ISO, RoHS, CE
• Condition: New
• Model NO.: GW-23LW
• Frequency Range: 1800MHz+2100MHz
• Application: Basement, Hotel,Office
• Working Time: Uninterrupted
• Gain: 75dB
• Output Power: 23 dBm
• Coverage: About 2500sqm
• Transport Package: Neutral Packing
• Specification: CE, RoHS
• Trademark: Greetwin
• Origin: Shenzhen
• HS Code: 8543709200
• Production Capacity: 2, 000PCS/Month

Product Description

23dBm 3G 4G Band1 Band3 LTE1800 WCDMA2100 Dual Band Signal Repeater

Model: GW-23DW

Tri-Band Signal Booster series is an ideal solution for three wireless system in small/medium businesses and home users looking to enhance indoor 2G&3G&4G wireless connectivity. It is connected via coaxial cable to Tri-Band Donor Antenna and Service Antenna, Tri-Band Donor Antenna is placed outside the building where it has easy access to BTS signal, and the Service Antenna is placed in the building where it can extend radio coverage to the blind area.







Features:
1. Cost effective solution for weak signal zones, reduce drop/off calls.
2. Compact size, low power consumption, easy installation, great cover.
Expansion and extention of the signal of base station. Optimization of the quality of the signal and source
3. Cover about 500~3000m² Without block or obstruct.
4. High linear design, ALC function design, low interference to BTS.
5. Support any cellular devices (voice & data & video)
6. Wide band signal booster, or customize selective band booster.
7. Support System CDMA800, GSM, DCS, PCS, WCDMA, UMTS,LTE 4G etc

Recommended Accessories:
1)Donor antenna: Log Periodic Antenna (9dBi, 806-960/1710-2700MHz)
2)Service antenna: Omni Ceiling Antenna (3dBi, 806-960/1710-2700MHz)
3)5D-FB coaxial cable with connecter (Cable length optional)

Application:
To expand signal coverage of fill signal blind area where signal is weak or unavailable.
Indoor: Hotels, Home, Basements, Shopping Malls, Offices, Parking Lots, Shop. Etc.

FrequencyRange			Uplink	Downlink
LTE1800+WCDMA			1710 - 1785/ 1920 - 1980MHz	1805 - 1880/ 2110 - 2170MHz
Gain			70dB	75dB
Output Power			20dBm	23dBm
Band width			Wide Band
Manual Gain Control			31dB / 1dB Step
Automatic Gain Control			> 20dB
Ripple in-band			≤ 8 dB
Return loss			≤ -10dB
Noise Figure			≤ 6dB
Spurious Emission &Intermodulation	9KHz~1GHz		≤ -36dBm
	1~12.75GHz		≤ -30dBm
WCDMA	Spurious Emission Mask		Meet 3GPP TS 25.143 ( V 6.2.0 )
	Modulation Accuracy		≤ 12.5%
	Peak Code Domain Error		≤ -35dB@Spreading Factor 256
Time Delay			≤ 1.5 μs
Frequency stability			≤ 0.01ppm
MTBF			> 50000 hours
Impedance			50 ohm
Power Supply			AC100-240V,DC10V/6A
Power LED			Power Indicator
Mechanical Specification
RF Connector		N-Female
Switch		Power Switch\Manual Gain Control Switch
Cooling		Heatsink Convection cooling
Humidity		< 90%
Operating Temperature		-10'c~55'c
Environment Conditions		IP40
Installation Type		Wall Installation
Size		268mm*58mm*189mm
Weight		< 4.5Kg

Installation Diagram

      Q1. Why is there still no signal after installing the equipment?

            1. Check the power on booster and power supply.

            2. Check the connector of outdoor antenna is tight or not.

            3. Check the connectors of RF cable are tight or not.

            4. Check the outdoor signal is strong enough or not.

            5. Check to make sure the antenna is installed correctly.

            6. Check the connector of indoor antenna is tight or not.

            7. Check the cable type is suitable or not.

 

      Q2. Why the signal strength is too weak on the edge of area?

            1. Check the outdoor signal and antenna direction.

            2. Check booster is full gain or not.

            3. Check all of the connectors are tight.

            4. Change the location of outdoor/indoor antenna.

            5. Check the cable type is suitable or not.

            6. Deploy more indoor antennas.

 

      Q3. After running booster, why the signals are not stable?

            1. Checking the distance between donor antenna and server antenna are too close to each other? Check LED

                of booster to make sure alarms are green.

            2. Checking the signals from donor antenna whether to be stable or not?

            3. Connect the system again if it is incorrect connection.

 

      Q4. Why the booster power LED is not bright?

            1. Checking the input AC power range indicated on power adapter whether is corresponding to the local

                power system.

            2. Checking the power adapter whether connect the equipment correctly and stably or not.

            3. Checking the power adapter whether damage or not. To test output voltage whether be corresponding to

                that indicated on power adapter or not by multimeter