Customization: | Available |
---|---|
Type: | Signal Repeater |
Transmission Medium: | Cable |
Suppliers with verified business licenses
Audited by an independent third-party inspection agency
Greetwin Smart Signal Repeater 23dBm Booster 3G 4G 5G Five Band 800 900 1800 2100 2600 B20 B8 B3 B1 B7 Cell Phone Signal Booster
Specification |
Uplink |
Downlink |
|
Frequency |
LTE800 | 832MHz-862MHz | 791MHz-821MHz |
GSM900 | 890MHz-915MHz | 935MHz-960MHz | |
LTE1800 |
1710MHz-1785MHz |
1805MHz-1880MHz |
|
UMTS2100 |
1920MHz-1980MHz | 2110MHz-2170MHz | |
LTE2600 | 2500MHz-2570MHz | 2620MHz-2690MHz | |
Operation Bandwidth |
Wide Band |
||
Gain |
≥70dB |
≥75dB |
|
Output Power |
≥20dBm |
≥23dBm |
|
MGC (Manual Gain Control) |
31dB Range/1dB step |
||
Ripple in Band |
8dB |
||
Noise Figure |
≤ 6dB |
||
VSWR |
≤2.0 |
||
ALC |
25dB |
||
Intermodulation Products |
≤ -40dBc |
||
Spurious Emission |
9KHz~1GHz |
≤ -36dBm/30KHz |
|
1GHz~12.75GHz |
≤ -30dBm/30KHz |
||
Frequency stability |
≤ 0.01ppm |
||
MTBF |
> 50000 hours |
||
Time Delay |
≤1.5μs |
||
Impedance |
50Ω |
||
Power Supply |
Input: AC 110~240V; Output: DC 10V/6A |
||
LED Alarm |
Power LED |
DC ON/OFF |
|
Smart LED |
Smart function ON/OFF |
||
AGC Alarm |
Alarm RED when ALC 5dB-10dB |
||
ISO Alarm |
Alarm RED when ALC 20dB-25dB, Then Repeater will Auto Shut Down. Auto restart after two minutes. |
||
Mechanical Specification |
|||
RF Connector |
N-Female |
||
Power Consumption |
25W |
||
Operating Temperature |
-10ºC~ +55ºC |
||
Environment Conditions |
IP40(Indoor) |
||
Installation Type |
Wall Installation |
||
Dimensions (D x W x H ) |
400*170*65mm |
||
Weight |
≤ 7 KG |
Q1. Why is there still no signal after installing the equipment?
1. Check the power on the booster and power supply.
2. Check the connector of the outdoor antenna is tight or not.
3. Check the connectors of the RF cable are tight or not.
4. Check the outdoor signal is strong enough or not.
5. Check to make sure the antenna is installed correctly.
6. Check the connector of the indoor antenna is tight or not.
7. Check the cable type is suitable or not.
Q2. Why the signal strength is too weak on the edge of the area?
1. Check the outdoor signal and antenna direction.
2. Check booster is full gain or not.
3. Check all of the connectors are tight.
4. Change the location of outdoor/indoor antenna.
5. Check the cable type is suitable or not.
6. Deploy more indoor antennas.
Q3. After running booster, why the signals are not stable?
1. Checking the distance between donor antenna and server antenna are too close to each other? Check LED of the booster to make sure alarms are green.
2. Checking the signals from donor antenna whether to be stable or not?
3. Connect the system again if it is incorrect connection.
Q4. Why the booster power LED is not bright?
1. Checking the input AC power range indicated on power adapter whether is corresponding to the local
power system.
2. Checking the power adapter whether connect the equipment correctly and stably or not.
3. Checking the power adapter whether damage or not. To test output voltage whether be corresponding to
that indicated on power adapter or not by multimeter