Ascom 23dBm Dual Band CDMA/PCS Cellular Amplifier 850/1900MHz Signal Repeater Booster 2g 3G 4G

• Customization: Available
• Type: Signal Repeater
• Transmission Medium: Cable
• Model NO.: GW-23GW-ASC
• Standard: Standard
• Lightning Protection: With Lightning Protection
• Certification: ISO, RoHS, CE
• Condition: New
• Dual Band: 900+2100/900+1800/850+1900
• Product Name: Cellphone Signal Repeater
• Application: Office,Basement, Hotel
• Transport Package: Neutral Packing
• Specification: CE, RoHS
• Trademark: Greetwin
• Origin: Shenzhen
• HS Code: 8543709200
• Production Capacity: 2, 000PCS/Month

Product Description

Double Band Signal Repeater 23dBm GSM 900MHz WCDMA 2100MHz 2g 3G 4G Lte Amplifier Cell Mobile Phone Signal Booster
Model: GW-23GW-ASC

Frequency Range			Uplink			Downlink
GSM900+WCDMA2100			890-915/1920-1980MHz			935-960/2110-2170MHz
LTE2600			2500-2570MHz			2620-2690MHz
CDMA 800/GSM 850			824-849MHz			869-894MHz
GSM 900			890-915MHz			935-960MHz
AWS1700			1710-1755MHz			2110-2155MHz
DCS 1800			1710-1785MHz			1805-1880MHz
PCS 1900			1850-1910MHz			1930-1990MHz
WCDMA/3G 2100			1920-1980MHz			2110-2170MHz
Gain			70dB±2db		75dB±2db
Output Power			20dBm±2dbm		23dBm±2dbm
Bandwidth			Wide Band
Manual Gain Control			31dB     / 1dB Step
Automatic Gain Control			>20dB
Ripple in-band			≤ 6dB
Return loss			≤ -10dB
Noise Figure			≤ 6dB
Spurious Emission &Intermodulation		9KHz~1GHz	≤ -36dBm
		1~12.75GHz	≤ -30dBm
WCDMA		Spurious Emission Mask	Meet 3GPP TS 25.143 ( V 6.2.0 )
		Modulation Accuracy	≤ 12.5%
		Peak Code Domain Error	≤ -35dB@Spreading Factor 256
Time Delay			≤ 1.5 μs
Frequency stability			≤ 0.01ppm
MTBF			> 50000 hours
Power Supply			AC100-240V,DC9V/5A
Power LED			Power indicator
Alarm LED	Red		Autoexcitation or High Power
	Green		Standard
Mechanical Specification
RF Connector			N-Female
Switch			Power Switch\Manual Gain Control Switch
Cooling			Heatsink Convection cooling
Impedance			50 ohm
Humidity			< 90%
Operating Temperature			-10°C~55°C
Environment Conditions			IP40
Size			250mm*170mm*53mm
Weight			< 3.5Kg

Features:
1. Cost-effective solution for weak signal zones, reduce drop/off calls.
2. Compact size, low power consumption, easy installation, great cover.
Expansion and extension of the signal of the base station. Optimization of the quality of the signal and source
3. Cover about 500~1500m² Without block or obstruct.
4. High linear design, ALC function design, low interference to BTS.
5. Support any cellular devices (voice & data & video)
6. Wideband signal booster, or customize selective band booster.
7. Support System CDMA800, GSM, DCS, PCS, WCDMA, LTE 4G etc

Advantages:
1. Smart Function, Intelligent mode setting
smart function called which can be activated via the front panel.
users can adjust gain and choose working band by LED panel, This smart function is easier than DIP Switch, can set up parameters, It is a simple, safe, and effective way.
2. Auto Level Control
The 30dB ALC is used to maintain steady output power even when the donor source signal fluctuates.

Standard Package:
1) AC90-264V, DC9V/5A power supply adapter 1PCS
2) AC power cord (EU/US/UK/SA/China standard, etc) 1PCS
3) Installation kit 1PCS
4) User manual 1PCS

Recommended Accessories:
1) Donor antenna: Log Periodic Antenna (9dBi,806-960/1710-2700MHz)
2) Service antenna: Omni Ceiling Antenna (3dBi,806-960/1710-2700MHz)
3) 5D-FB coaxial cable with connecter (Cable length optional)

 Advantages:
1. Smart Function, Intelligent mode setting
smart function called which can be activated via the front panel.
users can adjust gain and choose working band by LED panel, This smart function is easier than DIP Switch, can set up parameters, It is a simple, safe, and effective way.
2. Auto Level Control
The 30dB ALC is used to maintain steady output power even when the donor source signal fluctuates.
Application:
To expand signal coverage of fill signal blind area where the signal is weak or unavailable.
Indoor: Hotels, Home, Basements, Shopping Malls, Offices, Parking Lots, Shop.etc.

Method of Installation:
The booster is fixed onto the wall through expansion bolts.
A.  Drill holes in the selected place and install expansion bolts.
B.  Align the holes with the expansion bolts, place flat washers, spring washers, and nuts in turn, and tighten the nuts to fasten the installing support.
C. Place the booster on and fasten it.
D. Connect cables and power cables to the booster respectively.
 E. After installing the booster as described above, power on the booster to check the operation status.

Connection
A.  BTS Port: donor antenna cable is connected with Outdoor Port;
B.  MS Port: service whip antenna is connected with Indoor Port;
C.  DC IN: connected with Power adaptor.

                                           FAQ:

     Q1. Why is there still no signal after installing the equipment?

            1. Check the power on booster and power supply.

            2. Check the connector of outdoor antenna is tight or not.

            3. Check the connectors of RF cable are tight or not.

            4. Check the outdoor signal is strong enough or not.

            5. Check to make sure the antenna is installed correctly.

            6. Check the connector of indoor antenna is tight or not.

            7. Check the cable type is suitable or not.

 

      Q2. Why the signal strength is too weak on the edge of area?

            1. Check the outdoor signal and antenna direction.

            2. Check booster is full gain or not.

            3. Check all of the connectors are tight.

            4. Change the location of outdoor/indoor antenna.

            5. Check the cable type is suitable or not.

            6. Deploy more indoor antennas.

 

      Q3. After running booster, why the signals are not stable?

            1. Checking the distance between donor antenna and server antenna are too close to each other? Check LED

                of booster to make sure alarms are green.

            2. Checking the signals from donor antenna whether to be stable or not?

            3. Connect the system again if it is incorrect connection.

 

      Q4. Why the booster power LED is not bright?

            1. Checking the input AC power range indicated on power adapter whether is corresponding to the local

                power system.

            2. Checking the power adapter whether connect the equipment correctly and stably or not.

            3. Checking the power adapter whether damage or not. To test output voltage whether be corresponding

                to that indicated onpower adapter or not by multimeter.