1W Egsm Dcs Signal Repeater Band 3 Band 8 Mobile Signal Booster

• Type: Signal Repeater
• Transmission Medium: Cable
• Standard: Standard
• Lightning Protection: With Lightning Protection
• Certification: ISO, RoHS, CE
• Condition: New
• Model NO.: GW-30ED
• Dual Band: Egsm900MHz+Dcs1800MHz
• Product Name: Cellphone Signal Repeater
• Application: Office,Basement, Hotel
• Transport Package: Neutral Packing
• Specification: CE, RoHS
• Trademark: Greetwin
• Origin: Shenzhen
• HS Code: 8543709200
• Production Capacity: 2, 000PCS/Month

Product Description

1W EGSM DCS Signal Repeater Band 3 Band 8 Mobile Signal Booster
Model: GW-23ED
 

Frequency Range			Uplink		Downlink
EGSM900+LTE1800			880- 915/1710 - 1785MHz		925- 960/1805- 1880MHz
Max. Gain			75dB			80dB
Max. Output Power			23dBm			30dBm
Band width			Wide Band
Manual Gain Control			31dB     / 1dB Step
ALC			>20dB
Ripple in-band			≤ 8dB
Return loss			≤ -10dB
Noise Figure			≤ 6dB
Spurious Emission &Intermodulation	9KHz~1GHz		≤ -36dBm
	1~12.75GHz		≤ -30dBm
Time Delay			≤ 1.5 μs
Frequency stability			≤ 0.01ppm
MTBF			> 50000 hours
Power Supply			AC100-240V, DC9V/5A
Power LED			Power indicator
Impedance			50 ohm
Alarm LED		Red	Autoexcitation or High Power
		Green	Standard
Mechanical Specification
RF Connector				N-Female
Switch				Power Switch\Manual Gain Control Switch
Cooling				Heatsink Convection cooling
Humidity				< 90%
Operating Temperature				-10°C~55°C
Environment Conditions				IP40
Installation Type				Wall Installation
Size				268mm*58mm*439mm
Weight				< 8.5Kg

 

Features:
1. Cost effective solution for weak signal zones, reduce drop/off calls.
2. Compact size, low power consumption, easy installation, great cover.
Expansion and extention of the signal of base station. Optimization of the quality of the signal and source
3. Cover about 500~2000m² Without block or obstruct.
4. High linear design, ALC function design, low interference to BTS.
5. Support any cellular devices (voice & data & video)
6. Wide band signal booster, or customize selective band booster.
7. Support System CDMA800, GSM, DCS, PCS, WCDMA, LTE 4G etc

Advantages:
1. Smart Function, Intelligent mode setting
smart function called which can be activated via the front panel.
users can adjust gain and choose working band by LED panel, This smart function is easier than DIP Switch, can set up parameters,It is a simple, safe and effective way.
2. Auto Level Control
The 30dB ALC is used to maintain steady output power even when the donor source signal fluctuates.

Standard Package:
1) AC90-264V, DC9V/5A power supply adapter 1PCS
2) AC power cord (EU/US/UK/SA/China standard, etc) 1PCS
3) Installation kit 1PCS
4) User manual 1PCS

Recommended Accessories:
1) Donor antenna: Log Periodic Antenna (9dBi,806-960/1710-2700MHz)
2) Service antenna: Omni Ceiling Antenna (3dBi,806-960/1710-2700MHz)
3) 5D-FB coaxial cable with connecter (Cable length optional)

 Advantages:
1. Smart Function, Intelligent mode setting
smart function called which can be activated via the front panel.
users can adjust gain and choose working band by LED panel, This smart function is easier than DIP Switch, can set up parameters,It is a simple, safe and effective way.
2. Auto Level Control
The 30dB ALC is used to maintain steady output power even when the donor source signal fluctuates.
Application:
To expand signal coverage of fill signal blind area where signal is weak or unavailable.
Indoor: Hotels, Home, Basements, Shopping Malls, Offices, Parking Lots, Shop.etc.

Method of Installation:
The booster is fixed onto the wall through expansion bolts.
A.  Drill holes on the selected place and install expansion bolts.
B.  Align the holes with the expansion bolts, place flat washers, spring washers, and nuts in turn, and tighten the nuts to fasten the installing support.
C. Place the booster on and fasten it.
D. Connect cables and power cables to the booster respectively.
 E. After installing the booster as described above, power on the booster to check the operation status.

Connection
A.  BTS Port: donor antenna cable is connected with Outdoor Port;
B.  MS Port: service whip antenna is connected with Indoor Port;
C.  DC IN: connected with Power adaptor.

                                           FAQ:

     Q1. Why is there still no signal after installing the equipment?

            1. Check the power on booster and power supply.

            2. Check the connector of outdoor antenna is tight or not.

            3. Check the connectors of RF cable are tight or not.

            4. Check the outdoor signal is strong enough or not.

            5. Check to make sure the antenna is installed correctly.

            6. Check the connector of indoor antenna is tight or not.

            7. Check the cable type is suitable or not.

 

      Q2. Why the signal strength is too weak on the edge of area?

            1. Check the outdoor signal and antenna direction.

            2. Check booster is full gain or not.

            3. Check all of the connectors are tight.

            4. Change the location of outdoor/indoor antenna.

            5. Check the cable type is suitable or not.

            6. Deploy more indoor antennas.

 

      Q3. After running booster, why the signals are not stable?

            1. Checking the distance between donor antenna and server antenna are too close to each other? Check LED

                of booster to make sure alarms are green.

            2. Checking the signals from donor antenna whether to be stable or not?

            3. Connect the system again if it is incorrect connection.

 

      Q4. Why the booster power LED is not bright?

            1. Checking the input AC power range indicated on power adapter whether is corresponding to the local

                power system.

            2. Checking the power adapter whether connect the equipment correctly and stably or not.

            3. Checking the power adapter whether damage or not. To test output voltage whether be corresponding

                to that indicated onpower adapter or not by multimeter.